サイト内検索

詳細検索

ヘルプ

セーフサーチについて

性的・暴力的に過激な表現が含まれる作品の表示を調整できる機能です。
ご利用当初は「セーフサーチ」が「ON」に設定されており、性的・暴力的に過激な表現が含まれる作品の表示が制限されています。
全ての作品を表示するためには「OFF」にしてご覧ください。
※セーフサーチを「OFF」にすると、アダルト認証ページで「はい」を選択した状態になります。
※セーフサーチを「OFF」から「ON」に戻すと、次ページの表示もしくはページ更新後に認証が入ります。

2017年間ランキング

【HB】<丸善丸の内本店+ジュンク堂池袋本店>×hontoブックツリー 大切な人に贈るこどもの本(~1/10)

目次

  • 1.Introduction
  • 2.Basic theory
    • 2.1 Basic coordinate systems
    • 2.2 Fundamental requirement for contact and ratio of angular velocities
    • 2.3 Path of contact and its tooth profiles
    • 2.4 Tooth surface in the vicinity of a point of contact and limit of action
    • 2.5 Equations of motion and bearing loads
    • 2.6 Summary and references
  • 3.Design method of tooth surfaces for quieter gear pairs
    • 3.1 Conditions for no variation of bearing loads
    • 3.2 Equations of path of contact
    • 3.3 Limit of action and selection of path of contact
    • 3.4 Equivalent rack
    • 3.5 Surface of action,conjugate tooth surfaces,design reference bodies of revolution and tooth traces
    • 3.6 Contact ratios
    • 3.7 Design method for tooth surfaces of hypoid gears
    • 3.8 Design examples of tooth surfaces of hypoid gears
    • 3.9 Summary and references
  • 4.Involute helicoid and its conjugate tooth surface
    • 4.1 Definition of coordinate systems O2,Oq2,O1 and Oq1
    • 4.2 Equations of involute helicoid and a pair of involute gears in point contact
    • 4.3 Surface of action and conjugate tooth surface of an involute helicoid and a family of involute gear pairs
    • 4.4 Design method and example of face gears having involute helicoids for gear Ⅰ(pinion)
    • 4.5 Design example of face gears having an involute spur gear for gear Ⅰ(pinion)
    • 4.6 Summary and references
  • 5.Variation of tooth bearing and engagement error caused by assembly errors
    • 5.1 Movement of a point of contact and engagement error
    • 5.2 Calculated examples of variation of tooth bearing and engagement error
    • 5.3 Summary
  • 6.Rotational motion of gears and dynamic increment of tooth load
    • 6.1 Path of contact with its common contact normal at each point of a gear pair having modified tooth surfaces Ⅱ and tooth surfaces Ⅰ under no loads
    • 6.2 Paths of contact and their common contact normal at each point of a gear pair under load
    • 6.3 Equations of motion of gears
    • 6.4 Dynamic increment of tooth load and variation of bearing loads
    • 6.5 Dynamic increment of tooth load of a gear pair having a single flank error composed of symmetrical convex curves
    • 6.6 Verification by experiment through helical gear pairs having a single flank error composed of symmetrical convex curves
    • 6.7 Summary and references
  • 7.Design of a pair of tooth surfaces transmitting inconstant rotational motion
    • 7.1 Tooth surfaces Ⅰ and Ⅱ and a tooth surface of a rack transmitting inconstant rotational motion under a given center distance
    • 7.2 Tooth surface of a rack driven by a screw with constant lead and its mating tooth surface of gear Ⅰ(pinion)transmitting inconstant rotational motion
    • 7.3 Design examples
    • 7.4 Summary and references
  • 8.Summary

機械・機械製品 ランキング

機械・機械製品のランキングをご紹介します一覧を見る

前へ戻る

次に進む